| Thread | Last Post | Replies |
|
| Windows 98SE CD-Rom | 19 Jun 2004 11:25 GMT | 2 |
I need a Windows 98SE CD-Rom. I cannot find the CD-ROM supplied by Gateway for my computer and Gateway says they cannot supply another. I need the CD-ROM to install a file 'secur32.dll' required by Actiontec DSL modem. Any
|
| windows back but modem disappeared! | 19 Jun 2004 11:20 GMT | 1 |
Thanks both of you for that, it turned out my cd rom wasnt playing so I managed to load via my cdrw. Now the next problem (oh my I will learn the hard way!). Having got windows back I have the following problem with
|
| Purchase Window 98 SE? | 19 Jun 2004 00:11 GMT | 1 |
Any ideas as to where I can purchase a Windows 98 SE CD? I have a very old computer that runs Windows 98 very well but I need to make some repairs and I can't find my installation CD.
|
| getting around RAM requirement for broadband? | 18 Jun 2004 05:34 GMT | 4 |
I just did a reinstall of 98SE for a friend. I'm trying to set up her broadband service, but the DSL SetUp says the minimum RAM requirement is 64 MB. She only has 32 MB, and it's an old laptop, so upgrading isn't a viable option. She has been able to use DSL on this machine with ...
|
| missing files | 17 Jun 2004 16:53 GMT | 1 |
Hello I do hope that someone knows what I am talking about becuase I am not sure. I got an error that said that I am missing a DLL. file. I have just gotten SBC DSL they said that the problem is not related and that I have to.
|
| Drive Not Accessible | 17 Jun 2004 15:20 GMT | 4 |
Suddenly I cannot use my CDRom. All I get is a message saying "J:\is not accessible. The device is not ready". Device Manager says it is working properly but it isn't? I cannot load any new software now so I am really stuck.
|
| disk defragmenter | 17 Jun 2004 06:02 GMT | 1 |
Dear sirs, I am the owner of a windows 98se machine.due to the amount of files stored,my computer has become very slow.whenever i try to run disk defragmenter after going
|
| explorer | 17 Jun 2004 05:59 GMT | 1 |
every time I try to start up my pc it keeps putting a message up saying explorer as made an illegal operation so I close this down then I am just left with a blank back ground have tried re booting it but its not working
|
| URGENT HELP NEEDED !!!!!!!!!!!! LOW ON SPACE !!!!!!!!!!!! | 17 Jun 2004 05:09 GMT | 6 |
I don't know what happened but I'm severely low on disk space. I was in the living room and had about 400 mb or so of space left. I shut the laptop off and went into my bedroom where I started the computer back up. Now, it
|
| Compatibility Mode Paging reduces overall system performance | 17 Jun 2004 05:09 GMT | 1 |
I have Windows 98SE. My system got locked up and so I Control/Alt/Deleted to reboot. When it rebooted, it got the screen that shows what is in the autoexec.bat file and just stayed there. So, I Control/Alt/Deleted again,
|
| copying XP disks to a Win98 system | 17 Jun 2004 05:03 GMT | 1 |
I have had a hardware failure in my laptop running XP. I need to copy the contents of the drive to another computer running Win 98. I have an interface to connect the drive to the 98 system. However it will not read the drive. I
|
| Copy in Dos | 16 Jun 2004 23:50 GMT | 11 |
How would I us the Copy Commend in DOS to copy a 3 1/2 floppy to a folder on my harddrive? "Doing this in DOS not win" Thank You
|
| scan disk and defrag,too | 16 Jun 2004 23:37 GMT | 4 |
Scandisk tells me I have an error and, once it begins to repair it, I get another error that says "An error occured while scan disk was attempting to correct the previous error. Complete a thorough check of this drive,
|
| Change to Slave | 16 Jun 2004 23:35 GMT | 4 |
Im Havin problems booting my my WIN98SE computer. It keeps pulling a "Windows Protection Error" on me. I tried many of the steps in in KB article 188867 and article 302956 (except disabling items in Device manager and
|
| non system disk | 16 Jun 2004 23:14 GMT | 2 |
ok, i'm a moron. I cancelled an install of 98se from 3.1 and now I get the non-system disk error. The microsoft instructions tell me to type sys c: at the dos prompt, but I can't GET to a dos prompt. When I put in the
|