I had wireless running on my pc last year and then disconnected it. After
installing it again I have found that SSID is BTHomeHUB-4A1F and the MAC
address does not correspond with the address on the DI-524 Router. Can
anyone enlighten me as to what this *BTHomeHUB-4A1F* is and ...

I had wireless working for about a week then switched router off at mains ,
when i then tried to use my laptop again i cannot connect to internet (cannot
find server). Everything is fine with the netgear on my laptop except that it
states limited or no connectivity (the signal ...

Have just installed xp on a machine. From this machine I can access the
internet through ethernet cable through router switch. I can ping other
members of the WORKGROUP from this machine and can ping this machine
from anther member of the Workgroup. When I try to map a network drive

Greetings to All...
Am new to wireless but not to networking hardwired.  I installed a
wireless AP into a Ethernet Hub along with a wireless card in a
notebook.  I am confused about several things.  Been doing hours and

I look over all most all the groups to find the WZC doc or theory  or
FSM.But i can't find more useful informations.Anybody know these? May
you share it with us? Thanks.

I have a desktop computer using a wired connection to an ADSL router for the
Internet. I purchased an 802.11g USB adapter for this computer to be able to
share the Internet connection with my new Dell laptop, which uses an Intel
3945ABG adapter.

When I reinstall the driver for my wireless USB adapter (Netgear WG111v2) the
number of the connection changes. My original connection (which I take to be
#1) worked fine, but after reinstalling it connections  2, 3, and 4 did not.  
Now (after 4) when I install the driver the ...

About  a month and a half ago, I experienced inconsistent network services
from my IBM T43 laptop from some automated updates on the access connection
software and drivers for Wireless, Bluetooth and Dial-up.
Finally about 4weeks ago, the services on the laptop started crashing, ...

I have a wireless router (WPA enabled) connected to my dsl line, four
computers (A B C D) connected to a wired switch, and a wireless card in A
(windows xp pro).
I want to allow B C and D to access the internet through the wireless card

I upgraded from 256kb/s broadband to 2mb broadband. However even though my
internet gateway and wireless router have upgraded to the new faster
connection, my PC is still recieving the old 256k speed. Do I need to
configure my computer for the faster connection?

I replaced my old Microsoft MN700 with a new D-Link (DI-524) wireless G
router, set up the basement computer with the accompanying USB device and
immediately gained net access. No problem. But I have been having a horrible
time with the network setup wizard – something I’ve done ...

I have a Toshiba A105-S361 laptop. It came with Bluetooth installed. I now
have a Blackberry 7105t which also is equipped with Bluetooth. However, I
cannot get them to connect. I believe the problem is with my laptop. I have
never used the Bluetooth...when I first clicked on the ...

I have 4 computers connected with a wireless router.  I want to selectively
disable the internet connection to the kid's notebook computers from time to
time.  Is there a way to do that from my computer?  My notebook isn't a wired
connection; a family computer is the one wired. ...

I have a laptop with Ethernet and Wireless. Ethernet works fine. When I plug
the USB Wireless adapter in, that also works fine for a while then "dies". A
typical scenario is as follows:--I have been using the computer on teh
ethernet LAn all day (either at home or in the office, ...

I am trying to set up a wireles network: I have a Dell Demension 3000
hardwired to a cable modem and a Dell inspiron with a wireless NIC card in
it....When I run the wireless network setup wizare on the desktop; it does
fine until it asks me to use a flash card to create network ...