i got an USB HD enclosure for 3.5 HDs. It's got its own power supply.
everything seems ok. it's recognized. It's when I'm copying files. I
can copy files bu it suddenly stops, disappears from My Computer. Light
is still on. external HD is still runnning. But windows can no longer

Looking for a utility program I put the Intel motherboard disk from one
computer into another.  The CD was a self starting bios install disk.  Now
the computer I put it in is stuck with an endless loop:
Every day I start it up the "found new hardware" wizard starts up, but no

I have two drives and need to upgrade C drive to larger one. I plan to use
Ghost (or some other utility) to clone the drive. I hope that I can use a
USB 2.0 IDE inteface (Drive Kit) for the cloning instead of physically
installing the new drive in the PC. Do I need to get sysprep ...

Can the RAM be Combatible before i install my VGA driver and be
un-combatible when i install them :S
My Whole System Works Fine W/o installing the VGA drivers ,
Can the RAM be Uncombatible and Run the whole system w/o any problem

hi i would like some help i have put in another hard drive in my advent
computer if i switch the computer off and then turn it on again it will not
load it gets stuck on the advent words i put a 400 watt power supply unit in
but it still will not load but if i click it off and ...

I have a Wireless Notebook Optical Mouse.  Even though I do not have a
laptop, I like the "feel" of this mouse.  It is not my main mouse since it
is USB.  I now can not seem to left click (standard click) with it.  It
seems to work now and then.  I do believe the left button ...

yea I know windows provide VGA support by its deafult drivers but i
can't do any gaming on useing this drivers ,
anyway , before i format my system and work w/t the new DDR i was using
my VGA drivers that came w/t it w/o any problems @ all

One of my older computer's power supply failed yesterday. The unit was
replaced and the computer started up fine. However...
Some files on the secondary hard drive will not open. I get error messages
about corrupt file, invalid file format, unknown extension for random

i need to install a serial multiport on a windows system, to manage up
to 4 modems.
I'm looking for a stable device, with high quality modem so to have
best handshake as possible.

The subj HDD was installed in a newly built PC but despite being 200GB
(detected by BIOS at startup) is only showing as ~128GB by XP both in My
Computer and Disk Manager.  The latter shows it as a single partition/
healthy HDD but with teh 128GB capacity .  Retailer suggested a ...

I am running Windows XP Home SP2 on two computers.
I copy 10 Mb of files to a blank CD.  Under Properties I see that the CD
contains 10 Mb of files.  I also see that the capacity of the disk is 10
Mb.  I copy five Mb of files to the CD.  Under Properties I see that the CD

I have a laptop where I can not use DHCP correct with it.  My office network
is based on 192.168.254.xxx/255.255.255.0 (do not ask!  My client networks
are all lower than this!) and when ever I connect the laptop I get an
"auto-assigned" IP address of 169.254.xxx.yyy/255.255.0.0. ...

One of a sudden my HP Deskjet 5550 stopped working.  Have had it working fine
for 3 years now.  Tried to uninstall and re-install to no avail.
Installation goes fine, ithe installation routine even prints out a sample
page, but after the installation completes, that's it, no more ...

One of my older computer's power supply failed yesterday. The unit was
replaced and the computer started up fine. However...
Some files on the secondary hard drive will not open. I get error messages
about corrupt file, invalid file format, unknown extension for random

I took the general consensus and installed a PCI IDE controller. I
installed the drivers for it (Silicon Image SIL0680 by Syba). The Asus
motherboard sees it in the BIOS. The boot order is correct: My SATA
drive and then the SCSI drive on the new controller. However I can't