I want to get one or more network ready drives, but can't find any that
specifically state they have drivers for x64.  Any hints?  TIA

Hi, my first question (and probably not my last)! to the board.
Please accept my apologies if this issue has already been covered.
I have a laptop with an integrated cd/dvd rw combo. I have in the past
sucessfully played and burnt both music and films with no issue.

I have a 80GB hitachi Travelstar in a USB HDD Case. my system does
recognise it as USB Mass storage but doesnot assign a drive letter.
When I do in disk management i don't see this drive.
Start>Control Panel.>Administrative Tools>Computer Management>Disk

I have a Western Digital 100GB external hard drive that I use for backup.
The drive has two partitions of 20GB and 80GB. When I try to defrag the
drive, it runs for a couple of seconds and then terminates with the
following message:

My sister is always complaining about slow connection on her dial up.Finally
I checked it today and its the pits -14 at best on a Conexant Smart HSF1 V92
pci.
I checked the Telephone line with my laptop and I can get 52bps -so its the

First - is this the proper forum for this type of question?
Second - has anyone been successful in running Windows XP on a Dell
PowerEdge 1850? If yes, any issues?
Thanks!

For the past 2-3 years, I have been putting my computer on standby (I
would later find out it was S3) instead of turning it off. My mobo is
Soyo KT333 Dragon Plus and I used to have a 300W Enermax PSU. Recently,
I got a third hard drive and after a short while of using it, I started

I'm using a HL-DT-ST CD-RW GCE-8525B (its just a CD reader burner for all I
know) by the LG company. Now for some reason, it won't open anymore for the
last few days. I try using the eject button, doesn't work; I went to My
Computer and tried to make it eject than way, same ...

I know my machine only has low speed USB ports and I'm OK with that. When I
plug in a hi-speed USB device I get the normal pop-up telling me that my
"device can perform faster..."  I've search for the answer and everybody says
to go to device manager, select the properties tab of ...

Relatively new system has been running fine, but would
like to use full DLL cache. So increased the amount of
memory for protected mode and ran sfc /scannow.
On rebooting system continues to give the 0x0000007e

I found some corrupt files and deleted them but now performance is slow on
some applications.  When I try to run error-checking with "scan for and
attempt to recover bad sectors" on the hard drive, it locks everything up
about phase 4 of the scan.  I've run spyware and virus ...

Recently I went to play a video from my second hard drive and the
audio/video was very choppy. I went to check it under device manager
and it was set DMA if available/ DMA Mode 2. I then checked it in bios
but it was set to DMA Mode 5 there. Anyone know how I can change this

I have a viewsonic USB keyboard. It is becoming more frequent that it
disconnects itself for no reason I can find. The only way for me to use it is
to physicly remove the plug and then plug it back in. Yes it is a easy work
around but I shouldnt have to do it. Please give me some ...

ive got a dual boot system (xp pro and mandriva 2006)
its got a 1.8g amd processor and 256 sdram, im wanting to add extra
memory as ive got a few spare strips of 128 sdram all pc133 slot same
as my board. when i add a strip and turn on the pc , after it gets to

I have been searching and can not find the answer. I am hoping someone can
help here.
I am looking to overhaul this computer into another computer case. My
problem is, I want to replace the aging power supply but am very unfamiliar